Tutorial Step by Step Guide to Building Your Custom Gaming PC

1. Prepare your PC case

The first thing youll want to do is strip the case down as far as you can go. Remove every panel that you can, and store them in a safe place (inside the case box is the best bet). We recommend using a bowl (or a magnetic parts tray if you want to be fancy) to hold your screws throughout your PC building process.

2. Install your fans

If youve purchased some replacement or extra cooling fans, now is the time to install them where you need them. Try to keep your cooling setup balanced, so theres as much air being drawn in as is being blown out. In case youre not sure which way the wind will go, the plastic fan guards usually denote where the air will come through.

Typically you want two fans in the front drawing air in and at least one in the rear blowing air out. You could also screw one or two more optional fans into the roof of the PC case for additional exhaust if your PC case has mounting points for them.

3. Install the motherboard

Before we get to install one of the best motherboards, youll want to check on a few things about your PC case. Check for pre-installed motherboard standoffs, ensure the number and arrangement of them conforms to the holes found on your motherboard.

Secondly, see if your PC case has a large CPU cutout or window cut into the back of the motherboard frame. If it doesnt you may want to install any CPU cooler backplates and M.2 solid-state drives at this juncture.

Now thats done, first find your motherboards rear I/O shield, and push it into the rectangular slot in the back of your PC case. Make sure its right side up by matching the pattern of cutouts to the arrangement of ports on the back of your motherboard.

Next, lay your motherboard down inside the chassis carefully lining up its rear ports with the corresponding holes in the I/O shield you just installed on top of the standoffs installed in your chassis.

Then its a simple case of securing the motherboard down with the screws that came with your chassis. Make sure you use the right ones here, as you dont want to thread the standoffs, in case you need to remove it at a later date.

5. Install your memory

Next on the agenda is installing the best RAM to take care of your computer memory. Push down the latches at either ends of the DDR4 slots on your motherboard. Then line up the notch on the bottom of the memory with the notch in the slot. After that, you can install the memory by carefully pushing down both sides of the memory into the slot. You should hear a clicking sound as the memory secures into place and the latches click back up.

Make sure you use the farthest and second closest slot from the CPU if youre only using two memory sticks. Complete that and youll be good to go.

6. Install your CPU

Here's the last complicate piece in the PC building process, figuring out which of the best CPU coolers to go with.

Most third-party coolers require installing a backplate, which you may or may not have already done from step three of our PC building guide. Each individual cooler will have its own set of instructions your should follow, but the gist of most installations requires affixing a backplate and threading four pins though back of your motherboard.

From there youll want to thermal paste if your CPU cooler didnt come with any pre-applied already. Users will want to squeeze out a small blob, around the size of half a pea, onto the middle of the CPU. This will spread out once your cooler is mounted, and provide a sufficient amount of thermal interface material to successfully transfer heat from the processor die to the cooler of your choosing.

For air coolers, youll want to install most models with the fans unattached. Carefully orient the heatsink onto the pins or threads of the mounting plate and secure in place with any provided thumb screws or regular screws. After that, its simply a case of reattaching the fan to the tower, and plugging the 4-pin PWM fan header into the CPU Fan slot on the motherboard.

Liquid-coolers follow basically the same process, but require more upfront work. You'll probably have to attach fans onto the radiator and install it into your PC case in advance. Depending on which liquid cooler youre using, you may also need to plug in a second four-pin cable into a dedicated AIO cooler or optional cooler header on your motherboard.

This is also a good opportunity to plug in the rest of your system fans into any available slots on the board. Or alternatively, if your PC case has an integrated fan controller at the back of the chassis to route all your fans into, then directly onto the motherboard. Itll also need to connect to the motherboard via USB header.

7. Install your storage

Once the memory is in, its time to focus on some non-volatile memory storage, the best hard drives and best SSDs (solid-state drives). Our NZXT H400i happens to have a small SSD bracket on the front. Installing 2.5-inch drives into these caddies is a cinch, as you can simply slide it into place with the option of fully securing it with four screws.

Most modern PC cases comes with SSD bays of some sort. But if youre case doesnt, the 3.5-inch drive caddies typically reserved for hard drives should have compatible mounting points. No matter what type of storage drive youre installing, ensure the connection ports are facing towards a cable cut-out inside your chassis as it will make routing cables easier.

8. Position and install power supply

Now youve got your motherboard, CPU and memory installed youre going to want to choose the best PC power supply to run your new PC and then install it. If youve got a modular PSU, figure out what cables you need ahead of time, and plug them into your power supply first.

If your PC case comes with a PSU bracket, remove it ahead of time and attach it to the back of the unit. Next up thread the cables through the PSU slot in the back of the case first, and then slide the PSU into place, securing the bracket back onto the chassis.

Otherwise, on older cases youll have to slip in the power supply in through the inside of the chassis and push it firmly against the inside wall as you attach it with four screws.

Depending on the design of your case, youll want to orient the fan towards ventilation areas built into it. For most cases we suggest facing the fan downwards or to the side away from the interior of your PC. This way, your PSU can draw in fresh air and exhaust heat through the back.

9. Connect everything to your motherboard

To get your front I/O power buttons working properly, you need to plug in the correct cables. Fortunately, on our NZXT H400i, this is a single block that plugs directly onto the front I/O headers on the motherboard, make sure you orient it the correct way, then push it into place on the pins.

For everyone else, take the individual pins, and, using the motherboard installation handbook, identify which pins and cables need connecting. Try to do this part gently do, so as to not to bend the pins. Its important to note that any LED lights (HDD and Power), need to be oriented correctly, with the + and - cables installed into the + and - pins on the board.

Its also a good time to plug in your USB 3.0 header, USB 2.0 header, and audio passthrough. Audio is located on the bottom left of most motherboards. It will be labeled, and the pinouts will be different to the USB 2.0 headers. Install your USB 3.0 cables (denoted with a blue-colored end) into any available slots on the board, making sure to line up the pins with the holes in the USB 3.0 cables.

10. Connect your power supply

Now you can plug in the rest of your power cables.

Identify your 8-pin EPS cable, and slide it up the back of the chassis, through the cable grommet and plug it into the 8 pin power slot at the top of the motherboard. Then, find the bulkier 24-pin cable, slide that through any cable routing recesses on the chassis and plug it into the corresponding 24-pin ATX power port on the motherboard.

Next up, take your SATA power and connect it to any storage drives. If you happen to have something mounted onto the front of the case, run this SATA power cable through the PSU shroud, appropriate grommets or holes, and into your front-mounted 2.5-inch drive. This is a good opportunity to plug in the SATA Data cables between any storage drives and the motherboard as well.

Lastly, youll want to thread your PCIe power cable through the cutout in the PSU cover or any side grommets/holes, so that its ready for when you install your GPU.

11. Installing your graphics card

Finally, we have the last piece of the puzzle to slot into place.

First, take a look at your motherboard and locate the PCIe slot closest to your processor. From there locate the two PCIe slots next to where youll want to install your GPU and remove them. In most PC cases, thatll involve undoing two screws on the PCIe slot covers and removing them.

Take your graphics card out of the anti-static bag and line it up with the slots we just opened up. The rear I/O on the GPU should be facing out the back of the chassis. Once the gold contacts on your GPU make are touching the PCIe slot, gently push it into place until you hear a click. Then use the same screws we removed from the PCIe slot cover to secure the GPU into place.

Then its simply a case of plugging your PCIe power that you routed in with our last step and we have a fully built PC (mostly).

12. Turn on your PC

Finally, we have the last piece of the puzzle to slot into place.

First, take a look at your motherboard and locate the PCIe slot closest to your processor. From there locate the two PCIe slots next to where youll want to install your GPU and remove them. In most PC cases, thatll involve undoing two screws on the PCIe slot covers and removing them.

Take your graphics card out of the anti-static bag and line it up with the slots we just opened up. The rear I/O on the GPU should be facing out the back of the chassis. Once the gold contacts on your GPU make are touching the PCIe slot, gently push it into place until you hear a click. Then use the same screws we removed from the PCIe slot cover to secure the GPU into place.

Then its simply a case of plugging your PCIe power that you routed in with our last step and we have a fully built PC (mostly).

13. Clean up your cables (optional)

Now that were sure the machine is working, disconnect it again and bring it back to your workspace. Its worth doing this because youll want to reattach all those PC case panels and tidy up any loose cables.

That means using cable ties to bunch together cables as much as you can. Most PC cases come with cable cut-outs to use as tie-down points. Where there arent any, we usually use thicker cables to help push smaller ones flush against the inside of our computer chassis.

14. Install Windows (or the operating system of your choice)

Bring the system back to your computer space, where itll sit forever or at least until your next upgrade as well want to install the operating system next.

Most modern rigs lack an optical drive to install your OS, so youll need to create a USB install on another PC. To do this, download the Windows 11 Media Creation Kit and then install Windows 11 onto a USB stick with at least 8GB of space.

Then, once its finished, simply plug it into your new system. Go back into your BIOS to tell your system to boot from the USB stick first. From there you can go through the prompts to install the operating system onto your new rig. Dont worry about not having a software key during installation, you can activate Windows 10 once you reach the desktop.

15. Desktop maintenance

Once youre finally logged on, head on over to the manufacturers website, find your motherboard, head to service, and download the correct chipset drivers for your system.

Ninite is a nifty tool to get all the programs you want fast without having to worry about installing each one individually is. On the Ninite site, you can select which programs you want, download the installer and let it run its magic. After that, go download and install the correct graphics driver for your card and youll be all set to sit back and enjoy.

What components do I need for my PC?

Gaming? Content creation? Everyday office work? All have different requirements.

These days, basically everyone needs a decent PC to get through life, but they come in so many shapes and sizes that it's important to know what you're trying to build before you even get started.

For instance, if you're just going to be using your PC to do daily office work like web browsing or writing up documents you don't need to drop thousands of dollars on a fancy gaming rig. Building a PC with something like the AMD Ryzen 5 5600G will get you a quick and responsive PC that will last you years, with enough graphics horsepower to get you through all tasks that most people experience on a day-to-day basis.

However, there are plenty of people that need something with a bit more oomph. Computers are legitimately more powerful now than they've ever been, and there's never been more options to build something that will tear through the best PC games like they were so much paper. But, powerful hardware like the Nvidia GeForce RTX 3080 and the AMD Ryzen 9 5900X come at a high price.

Luckily, if you're on more of a budget, you can get something like an Intel Core i5-11600K and an Nvidia GeForce RTX 3060 (if you can find one in stock at a decent price, that is), and have an incredible 1080p gaming machine. And, that will be able to get some video editing done on the side too.

What tools do I need to build a PC?

You may need fewer tools to build a computer than you'd assume.

Although a single phillips screwdriver is all you need to construct a PC, you may want a few more things on hand just in case. For example, needle nose pliers or a simple pair of tweezers may come in handy to place screws into tight places or retrieve them.

Zip ties are useful for tidying up all your PC cables and luckily, you most likely wont have to buy them as they often come included with several different types of computer parts. Youll also need a pair of side cutters (or just scissors) to cut those said zip ties.

You cant go wrong with an anti-static wrist strap, either though you can get away with not having one. Unless youve been running around on carpet all day, or have cats, you likely arent holding enough static charge to damage the electronics. Just do yourself a favor and discharge any latent electricity by placing your hand on metal, like your PC case or power supply.

As for your workspace, youre going to want to clear off a good bit of table space, as you'll likely be flipping your PC on its side, feet, back and any which way to install everything.

And, before we forget, its a good idea to get a monitor, keyboard and mouse set up before you start building, so you have something to plug it into when the building is done. You should also have a power socket and internet connection available.

Its hard to find a modern build with an optical drive these days, so put the Windows 11 installer onto a USB stick (we talk you through this in how to install Windows 11). If you cant find a handy thumb drive and a laptop, we would cannibalize an older rig for a CD drive, or even just buy one you can find them online for less than 10 bucks these days.

Get the hottest deals available in your inbox plus news, reviews, opinion, analysis and more from the TechRadar team.